揚州瑞浦DCL-50B無源觸點電動執行器
揚州瑞浦DCL-50B無源觸點電動執行器
1．電氣限位的調整 Adjustment of the limited location of electric
松開行程擋塊的螺釘，用螺絲刀輕敲行程擋塊，即可調整行程行行程開關擋塊的角度，從而改變電氣限位的開閉角度。后，切實緊固好行程擋塊的螺釘。5、10的行程擋塊和行程開關布局圖。
Unalamp the screw that the joumey blocked one, rap the journey and block one with the screwdriver, i.e. the adjustable journey blocks the angle of one, thus change the holding and closing the angle of the location of electric limit. Finally, fasten the screw that the good journey blocked one conscientiously. 2040／50／60／100200的行程擋塊和行程開關布局圖 20/40/50 60/100/200 of the travel block lumps and travel switch overall arrangement picture
2．電器位的調整（開度型、智能型 Adjustment(tum on one degree of types, inte)of the potentiometer
a．電位器的電阻值為1K2、5K2。
The resistance valve of the potentionmeter is 1kn, 5KO
b．用手柄轉動動閥門到全閉位置。
Rotate the valve and reach to close the position completely with the handle
C．松開電位器，轉動動電位器齒輪，用*表測量4－5接線端子間的電阻值，使4－5的電阻值到
52以下，緊固電位器固定螺釘。（如果是智能型的七線接插件連接時請測量對RV和RS兩插插孔的電阻值）
Unclamp the potentionmeter rotate the gear wheel of the potentionmeter measure the resistance valve among4-5wiring sons of end with the universal meter nable the resistance valve of 4-under 50, fasten the potentionmeter fixed screw.(if please measuer the resistance value to RV and RS two jake when being that intelligent Line seven connects the plug-in package connection
注：手動操作時，不能過分超出全開，全關的極限位置，轉角過大，會導致其部件的損壞
Note: At the time of manual operation, can t go beyond and is open excessively completel he terminal position that is closed completely. the comer is too big, will cause its part s damage
3．機械限位的調整
Adjustment of the mechanism spacing
a．用手柄轉動到全開位置
Rotate to completely opening position with the handle
b．松緊螺母，旋轉調整螺釘，使只與機械擋擋塊接觸，然后反方向旋轉螺釘半圈，鎖緊螺毋
Unclamp the locknut, rotate and adjust the screwenable it and machinery block one and keep in touch, then, rotate semi circke of screw, the locknut in the opposite direction
c．同樣的方法，可進行全閉位置的機械擋塊的調整。
The same method, can close the adjustment of blocking one of machinery of the position completely.
