防水卷材拉伸試驗機適用于各種防水卷材、涂料.橡膠、編織物及小截面金屬細絲。也可用于符合本試驗機條件時的其它試驗，使用前務必仔細閱讀說明書。并由 實驗人員操作，以避免操作不當引起的傷害。如需了解更多資料請與我公司客服人員聯系。
Waterproof coil tensile tester is suitable for various waterproof coils, coatings, rubbers, braids and small cross-section metal filaments. It can also be used for other tests that meet the conditions of this testing machine. Please read the instructions carefully before use. It is operated by experimental personnel to avoid injury caused by improper operation. For more information, please contact our customer service staff.
防水卷材拉伸試驗機由上海榮計達儀器科技有限公司提供，參照《GB/T328-2007系列》相關標準設計制造，具有造型美觀，設計合理，性能穩定，結構緊湊操作方便優點。
The waterproof coil tensile testing machine is provided by Shanghai Rongjida Instrument Technology Co Ltd. It is designed and manufactured in accordance with the relevant standards of "GB / T328-2007 Series".
防水卷材拉伸試驗機技術參數：
★大試驗力：5000N
★試驗力有效測量范圍：80N—2000N
★試驗力小分辨力：1N
★拉伸夾具間A大距離：800mm
★試驗速度：2-500mm 可調
★電源：220V±10％
Technical parameters of waterproof coil tensile tester:
★ Large test force: 5000N
★ Effective measurement range of test force: 80N—2000N
★ small test force resolution: 1N
★ A large distance between stretching fixtures: 800mm
★ Test speed: 2-500mm adjustable
★ Power supply: 220V ± 10%
防水卷材拉伸試驗機結構：
★本試驗機由底座、箱體立柱、夾頭、絲杠、軌道、電子測力系統、位移測量系統等零部件組成。
★機械加荷系統由下箱體內減速箱及絲杠組成。
★夾頭由支架、壓板、支柱、軋片、彈簧等主要零件組成，上夾頭與測力體相連，通過它所夾持的試件向上運動實現測力傳遞。
Structure of waterproof coil tensile tester
★ This testing machine consists of base, box post, chuck, lead screw, rail, electronic force measurement system, displacement measurement system and other components.
★ The mechanical loading system is composed of a reduction box and a screw in the lower box.
★ The chuck is composed of the main parts such as bracket, pressure plate, pillar, rolled sheet, spring, etc. The upper chuck is connected with the force measuring body, and the force transmission is achieved by the upward movement of the specimen held by it.
試驗機安裝：
本試驗機整臺裝箱出廠，安裝時應預先打好砼底座，高度應和本機相配，方便操作為宜，也可向本廠訂做底柜。本機設置應找水平，否則對拉力數值有影響，本機底部有四個底腳螺栓用以調整水平，接好地線即可使用。
Installation of waterproof coil tensile tester:
The whole test machine is packed in a box before leaving the factory. The base should be pre-dipped during installation. The height should be matched with the machine for convenient operation. The base cabinet can also be customized from the factory. The level of this machine should be set, otherwise it will affect the tension value. There are four foot bolts on the bottom of the machine to adjust the level, and the ground wire can be used.
調試與使用：
夾頭位置調整：
1、按面板上的上升按鍵,同時面板上狀態指示燈紅燈亮,相應速度檔位指示燈開始閃爍,液晶屏上狀態顯示位置:上升,同時實時顯示力值和移值,如果到達力值或位移的A大限制值,自動停機,同時液晶屏狀態位置顯示滿載或限位.
2、按面板上的下降按鍵,同時面板上的狀態指示燈綠燈亮,相應速度檔位指示燈開始閃爍,液晶屏上狀態顯示位置顯示[下降],同時實時顯示力值和移值.
3、按面板上的停止按鍵,同時面板上狀態指示燈熄滅,相應速度檔位指示燈停止閃爍保持常亮,液晶屏狀態顯示位置顯示停止.
速度調整：
按下相應的七個速度按紐中需要選擇一個便完成速度的調整,相應的速度指示燈會點亮,注意不要同時按下多個速度按紐.
Debugging and use of waterproof coil tensile testing machine:
Chuck position adjustment:
1.Press the up button on the panel.At the same time, the status indicator on the panel is red, and the corresponding speed gear indicator starts flashing.The status display position on the LCD screen: Ascend, and simultaneously display the force value and shift value in real time. Or the large A limit value of displacement, it will automatically stop, while the LCD screen status and position display full load or limit.
2.Press the down button on the panel, at the same time, the status indicator on the panel is green, the corresponding speed gear indicator starts flashing, the status display position on the LCD screen displays [Descent], and the force value and shift value are displayed in real time.
3.Press the stop button on the panel, at the same time, the status indicator on the panel goes out, the corresponding speed gear indicator stops flashing and stays on, and the LCD status display position display stops.
Speed adjustment:
Press the corresponding seven speed buttons to select one to complete the speed adjustment. The corresponding speed indicator will light up. Be careful not to press multiple speed buttons at the same time.
使用方法：
先按下面板上清零按扭,系統會自動進行拉力和位移零位校準,然后按下啟動按紐,同時面板上狀態指示燈亮紅燈,相應速度檔位指示燈開始閃爍,液晶屏上顯示力值和位置的A大值,如果滿足預定的停機條件,系統自動停機,液晶屏狀態自動顯示位置,斷裂,并保持A大力值和位移A大值,等待2s后系統,開始回車,同時面板上狀態指示紅燈亮,相應速度檔位指示燈開始閃爍,回到零位后系統自動停機,面板上狀態指示燈熄滅,相應速度檔位指示燈停止閃爍保持常亮,液晶屏上狀態顯示位置顯示有效. 按下啟動按紐后如人工按下停止按鍵系統自動停止,同時產生無效數據,并給出相應指示 在測試過程中如果拉力和位移到達大限制值,系統也自動停機,同時液晶屏狀態位置顯示滿載或限位.
Debugging and use of waterproof coil tensile testing machine:
Chuck position adjustment:
1.Press the up button on the panel.At the same time, the status indicator on the panel is red, and the corresponding speed gear indicator starts flashing.The status display position on the LCD screen: Ascend, and simultaneously display the force value and shift value in real time. Or the large A limit value of displacement, it will automatically stop, while the LCD screen status and position display full load or limit.
2.Press the down button on the panel, at the same time, the status indicator on the panel is green, the corresponding speed gear indicator starts flashing, the status display position on the LCD screen displays [Descent], and the force value and shift value are displayed in real time.
3.Press the stop button on the panel, at the same time, the status indicator on the panel goes out, the corresponding speed gear indicator stops flashing and stays on, and the LCD status display position display stops.
Speed adjustment:
Press the corresponding seven speed buttons to select one to complete the speed adjustment. The corresponding speed indicator will light up. Be careful not to press multiple speed buttons at the same time.
試驗機手動停車和自動停車方式的調整（請注意:切勿輕易調整）
按設置鍵,液晶屏顯示輸入密碼.密碼為22.按2次清零再按2次樣本密碼位置顯示22.輸入完畢.按設置鍵再按下打印鍵6次顯示回車狀態.按下樣本為手動回車,按下清零鍵為自動回車,按下設置鍵退出,調整完畢.注自動回車時可按下樣本鍵否則按停止鍵后數值不保持.
Adjustment of the manual and automatic stopping methods of the waterproof coil tensile tester (please note: do not adjust easily)
Press the set key, the LCD screen displays the input password. The password is 22. Press twice to clear and then press twice. The sample password position is displayed. 22. Input is complete. Press the set key and then press the print key 6 times to display the carriage return status. Press the sample For manual carriage return, press the zero key for automatic carriage return, press the set button to exit, and the adjustment is completed. Note When the automatic carriage return, the sample button can be pressed, otherwise the value will not be maintained after pressing the stop button.
系統狀態顯示位置顯示有效,按下面板樣本按紐,系統自動存儲當前測試數據,樣本數加1,如在其它狀態下按下樣本按紐,液晶屏狀態顯示均值,系統顯示目前測試過程中的全部樣品的平均值,如果再次按動按紐樣本按紐,液晶屏上狀態位置顯示瀏覽.同時開始存儲樣本由后到前的瀏覽.瀏覽完成A個樣本后,系統再次顯示平均值,再次準備樣本由前到后的瀏覽.按其他強鍵退出瀏覽.
The system status display position of the waterproof membrane tensile testing machine is valid. Press the sample button on the panel, the system automatically stores the current test data, and the number of samples is increased by 1.If you press the sample button in other states, the LCD screen displays the average value. Display the average value of all samples in the current test process. If you press the button again, the sample button will display the status on the LCD screen. At the same time, the storage sample will be browsed from back to front. After A sample is browsed, the system will be displayed again. The average value is displayed, and the sample is ready to be browsed from front to back. Press other strong keys to exit the browsing.
