FUEHLERSYSTEME傳感器DMU2/A
FUEHLERSYSTEME傳感器DMU2/A帶 EMC 螺紋的壓力差壓力傳感器
壓力傳感器 DMU2 / A 記錄兩個壓力出口處的過壓、欠壓和壓差，并將測量值轉換為 0-10 V 和 4-20 mA 的線性輸出信號。 可選擇8種不同的刻度，使用創(chuàng)新的撥碼開關技術可以自由切換。 壓力傳感器的輸出衰減（0 秒/1 秒/5 秒/10 秒）也可以使用 DIP 開關進行選擇。 對于零點的手動校準，壓力傳感器只需按一下按鈕即可在原位執(zhí)行零點平衡。 如果需要，可以使用 SPAN 控制器對壓力傳感器進行原位精細校準。 鋁制外殼確保了的機械堅固性，并帶有 EMS 螺紋，可輕松安全地進行符合 EMC 的接線。
-5000 ... + 5000 帕
EMC螺紋
每個設備 8 種不同的秤
0-10 伏，4-20 毫安
輸出衰減 0 秒 / 1 秒 / 5 秒 / 10 秒 通過 DIP 開關可選擇
型號：
DMU2/A-I/V10...+/-500 Pa4-20 mAwithout display
DMU2/A-I/V20...+/-5000 Pa4-20 mAwithout display
DMU2/A-U/V10...+/-500 Pa0-10 Vwithout display
DMU2/A-U/V20...+/-5000 Pa0-10 Vwithout display
DMU2/A-U/V30...+/-100 Pa0-10 Vwithout display
Pressure typepositive, negative or differential pressure
Mediumair, non-aggressive, non-flammable, non-condensing gases
Measurement range pressureV1: 0...+/-500 Pa, V2: 0...+/-5000 Pa, V3: 0...+/-100 Pa
ScalesV1: 0...+/-100, 0...+/-200 Pa, 0...+/-300 Pa, 0...+/-500 Pa; V2: 0...+/-1000, 0...+/-2000 Pa, 0...+/-3000 Pa, 0...+/-5000 Pa; V3: 0...+/-25, 0...+/-50 Pa, 0...+/-75 Pa, 0...+/-100 Pa
Accuracy±3,0% FS (at 20°C)
Temperature dependency±2,5% FS / 10 K
Linearity inaccuracy±1,0% final value
Long term stability±1% FS/year
Zero-point adjustmentmax. +2% final value
Offset±5% from the selected scale by 270° potentiometer
Reaction rate< 1 s, at 5% alteration relating to final value
Output attentuation0 s / 1 s / 5 s / 10 s selectable by DIP switch
Sensor protectionmounted inside housing
Running-in time< 30 min at initial operation because of tempering
Supply voltage analog 0-10 V24 V AC/DC (±5%)
Supply voltage analog 4-20 mA15...36 V DC (Ubmin = 15 V + RLoad*0,02A)
Current consumption at 0-10 Vtyp. 15 mA
Current consumption at 4-20 mAmax. 20 mA / output
Analogue output 0-10 V3-wire connection, min. load resistance 100 kOhm
Analogue output 4-20 mA2-wire connection (transmitter), max. RLoad(Ohm) = (+Ub - 15 V) / 0,02 A
Electrical connectionscrew terminals max. 1,5 mm2
Pressure resistance5-times of measurement range
Housingdie-cast (aluminium), colour silver grey like RAL 7001
DimensionsHousing: L 64 x W 58 x H 34,5 mm
Cable glandM16x1,5 high-strength cable glａnd with strain relief and EMC grounding
Protection typeIP65, IP20 if pressure connection port is open
Protection classIII
Working range r.H.0...98% r.H. in contaminant-free, non-condensing air
Working temperature0...+50°C
Storage temperature0...+50°C
InstallationHousing: screw fastening, Pressure connection: 2 plastic duct connecting nipple with fastening screws and 2 m PVC tube ? 6 mm (in scope of delivery)
Manual zero-point adjustmentThe zero point adjustment is started by pressing the button on the circuit board (push 10 s until LED stops flashing or by the display version the countdown 10-0 is completed). Before, a continuous operation of at least 1 hour must be sure, the offset must be in the middle position and the pressure inputs P+ and P- must be an obvious offense to the environment. The successful calibration will be signalized by 5 sec durable lightning of the LED.
ApprovalsCE, EAC, RoHS
