如下為我司愛澤工業IZE_Industries本月部分到貨FAAC/NICE電機相關產品，索取樣本資料和產品信息。

FAAC門電機C850愛澤工業izeindustries NICE門電機BM5024愛澤工業izeindustries

FAAC門電機C850描述及技術規格

General

These instruction apply to the following models: C850

The C850 is an electromechanical operator designed for moving sliding gates.

The non-reversing system is guaranteed by an electric brake that prevents manual movement of the sliding leaf when the motor is stopped, and therefore does not require an electric lock.

A handy manual release makes it possible to manoeuvre the gate in case of black-out or operator inefficiency

C850是一款專為移動滑動門而設計的機電操作器。

非反轉系統由電動制動器保證，防止電機停止時滑動葉片的手動移動，因此不需要電鎖。

非換向系統由電動制動器保證，當電機停止時，可防止滑動葉片的手動運動，因此不需要電動鎖。

便捷的手動釋放裝置可以在停電或操作效率低的情況下操縱門。

FAAC門電機C850規格大小

Installing the automated system

Preliminary checks

For the safety and correct operation of the automated system, ensure that the following conditions are met:

• The gate structure must be designed to be automated. In particular, the diameter of the wheels must conform to the weight of the gate being automated, there must be a guide on top and mechanical limit switches sized to suit the weight and speed of the movable leaf, to avoid derailment of the gate;

• Initially, leave at least 10 cm of clearance between the movable leaf stopping points (open and close) and the mechanical stops of the gate. The final adjustment is made once the inverter programming precedure is completed. Minimum distance 3 cm.

• The gate sliding rail must be linear and horizontal.

• Manual movement of the gate must be smooth along the entire stroke.

• The characteristics of the ground must guarantee sufficient solidity of the foundation plinth.

• No tubes or electrical cables should be present in the plinth digging area.

• If the gear motor is exposed to vehicle transite, provide for adequate protection against accidental impact, when possible.

• Ensure that there is an efficient earth plate for connecting the gearmotor.

Should various elements not need the above-mentioned conditions, adjust them so they do.

安裝自動化系統

初始檢查

為確保自動化系統的安全和正確運行，請確保滿足以下條件：

•門結構必須設計為自動化。特別是車輪的直徑必須符合自動門的重量，在頂部和機械限位開關上必須有一個導向裝置，以適應活動門葉片的重量和速度，以避免門脫軌;

•zui初，在可移動的葉節點（開啟和關閉）和門的機械停止點之間留出至少10厘米的間隙。zui終調整是在逆變器編程之前完成的，zui小距離3厘米。

•門滑軌必須是直線水平。

•手動門的移動必須在整個行程中保持平滑。

•地面的特征必須保證地基基座的堅固性。

•底座挖掘區域不應有管道或電纜。

•如果減速電機暴露在車輛的位置上，應盡可能提供足夠的保護以防意外碰撞。

•確保有一個有效的接地板用于連接減速電機。

FAAC門電機C850手動開關

我司FAAC門電機到貨圖集；

FAAC門電機C850及配件 愛澤工業izeindustries

NICE門電機BM5024及MB5024技術參數

愛澤工業(IZE INDUSTRIES)*經銷、常用備件型號；

NICE門電機MB4024

NICE門電機MB4005

NICE門電機MB4006

NICE門電機MB4015

NICE門電機MB4605

NICE門電機MB4615

NICE門電機MB5024

NICE門電機MB5015

NICE門電機MB5016

NICE門電機MB5615

NICE門電機BM5024愛澤工業izeindustries

以上為本月部分到貨FAAC/NICE電機相關產品，愛澤工業專業提供FAAC/NICE全系列產品，NICE門電機MB4024、FAAC門電機C85等等。

如果您有任何關于產品的相關技術咨詢或者需要產品的相關技術資料與文檔，請隨時愛澤工業（86-21-3100 6702），或者訪問www.ize-industries。。ｃｏｍ,我們將盡全力解決您的問題。