PV2R33系列日本YUKEN油研雙作用葉片泵

PV2R33-52-52-F-RAAA-31 PV2R33-52-60-F-RAAA-31 PV2R33-60-116-F-RAAA-31  

PV2R33-52-66-F-RAAA-31 PV2R33-52-76-F-RAAA-31 PV2R33-76-116-F-RAAA-31 

PV2R33-52-94-F-RAAA-31 PV2R33-60-52-F-RAAA-31 PV2R33-94-116-F-RAAA-31 

PV2R33-60-60-F-RAAA-31 PV2R33-60-66-F-RAAA-31 PV2R33-66-116-F-RAAA-31 

PV2R33-60-76-F-RAAA-31 PV2R33-60-94-F-RAAA-31 PV2R33-52-116-F-RAAA-31  

液壓泵自吸高度不超過500mm(或進口真空度不超過0.03MPa)，若采用補油泵供油，供油壓力不得超過0.5MPa，當供油壓力超過0.5MPa時，要改用耐壓密封圈。對于柱塞泵，應盡量采用倒灌自吸方式。液壓泵裝機前應檢查安裝孔的深度是否大于泵的軸伸長度，防止產生頂軸現象，否則將燒毀泵，液壓泵使用注意事項。

PV2R33-66-52-F-RAAA-31 PV2R33-66-60-F-RAAA-31 PV2R33-116-94-F-RAAA-31 

PV2R33-66-66-F-RAAA-31 PV2R33-66-76-F-RAAA-31 PV2R33-116-76-F-RAAA-31  

PV2R33-66-94-F-RAAA-31 PV2R33-76-52-F-RAAA-31 PV2R33-116-66-F-RAAA-31 

PV2R33-76-60-F-RAAA-31 PV2R33-76-66-F-RAAA-31 PV2R33-116-60-F-RAAA-31 

PV2R33-76-76-F-RAAA-31 PV2R33-76-94-F-RAAA-31 PV2R33-116-52-F-RAAA-31

液壓泵啟動時應先點動數次，油流方向和聲音都正常后，在低壓下運轉5～10min，然后投入正常運行。柱塞泵啟動前，必須通過殼上的泄油口向泵內灌滿清潔的工作油。 上海斜軸液壓泵啟東高壓告訴您液壓泵按液壓系統中常用的泵結構分為：齒輪泵，葉片泵,柱塞泵。

PV2R33系列日本YUKEN油研雙作用葉片泵